6ES7332-5TB00-0AB0 SIMATIC DP, HART ANALOG OUTPUT

6ES7332-5TB00-0AB0 SIMATIC DP, HART ANALOG OUTPUT

Product Code: 6ES7332-5TB00-0AB0

Availability: In Stock

Price: $227.42
Qty:
Add to Wish List
Add to Compare
  
 
Ex analog output module with HART

-
SIMATIC DP, HART ANALOG OUTPUT SM 332, 2AO, 0/4 - 20MA HART, FOR ET200M WITH IM153-2, 20 PIN
Supply voltage
Load voltage L+
Rated value (DC) 24 V
Reverse polarity protection Yes
Input current
from backplane bus 5 V DC, max. 100 mA
from supply voltage L+, max. 150 mA
Power losses
Power loss, typ. 3.5 W
Analog outputs
Number of analog outputs 2
Voltage output, short-circuit protection Yes
Current output, no-load voltage, max. 19 V
Cycle time (all channels) max. 5 ms
Output ranges, current
0 to 20 mA Yes
4 to 20 mA Yes
Connection of actuators
for current output two-wire connection Yes
Load impedance (in rated range of output)
with current outputs, max. 650 Ω
with current outputs, inductive load, max. 7.5 mH
Destruction limits against externally applied voltages and currents
Voltages at the outputs towards MANA max. 17 V / -0.5 V
Current, max. 60 mA / -1 A
Cable length
Cable length, shielded, max. 400 m
Analog value creation
Integrations and conversion time/resolution per channel
Resolution with overrange (bit including sign), max. 12 bit; Output value; 8 bit (+ sign) read back value
Conversion time (per channel) 40 ms
Settling time
for resistive load 2.5 ms
for capacitive load 4 ms
for inductive load 2.5 ms
Errors/accuracies
Output ripple (based on output area, bandwidth 0 to 50 kHz), (+/-) 0.02 %
Linearity error (relative to output range), (+/-) 0.03 %
Temperature error (relative to output range), (+/-) 0.01 %/K
Crosstalk between the outputs, min. 130 dB
Repeat accuracy in steady state at 25 °C (relative to output area), (+/-) 0.0050 %
Operational limit in overall temperature range
Current, relative to output area, (+/-) 0.55 %
Basic error limit (operational limit at 25 °C)
Current, relative to output area, (+/-) 0.15 %
Interrupts/diagnostics/status information
Substitute values connectable Yes; Parameterizable
Alarms
Diagnostic alarm Yes; Parameterizable
Diagnostic messages
Diagnostic functions Yes; Parameterizable
Diagnostic information readable Yes
Diagnostics Yes
Overrange Yes
Wire break Yes; as of output value > 0.5 mA
Wire break in actuator cable Yes
HART communication active Yes; green LED (H)
Diagnostics indication LED
Group error SF (red) Yes; Additional group message per channel
Channel error indicator F (red) Yes; per channel
Ex(i) characteristics
Module for Ex(i) protection Yes
Max. values of output circuits (per channel)
Co (permissible external capacity), max. 230 nF
Io (short-circuit current), max. 66 mA
Lo (permissible external inductivity), max. 7.5 mH
Po (power of load), max. 506 mW
Uo (output no-load voltage), max. 19 V
Um (fault voltage), max. 60 V; DC
Ta (permissible ambient temperature), max. 60 °C
Galvanic isolation
between the channels and backplane bus Yes
Galvanic isolation analog outputs
Galvanic isolation analog outputs Yes
between the channels Yes
between the channels and the load voltage L+ Yes
Permissible potential difference
between the outputs (UCM) 60V DC/30V AC
between M internally and the outputs 60V DC/30V AC
Isolation
tested with
Channels against backplane bus and load voltage L+ 1500 V AC
Channels among one another 1500 V AC
Load voltage L+ against backplane bus 500 V DC
Standards, approvals, certificates
FM approval Available soon
Use in hazardous areas
Type of protection acc. to EN 50020 (CENELEC) [EEx ib] IIC
Type of protection acc. to FM Class I, Division 2, Group A, B, C, D T4; Class I, Zone 2, Group IIC T4
Test number KEMA 97 ATEX 2359 X
Type of protection acc. to KEMA II3 (2) G Eex nA [ib] IIC T4
Dimensions
Width 40 mm
Height 125 mm
Depth 120 mm
Weights
Weight, approx. 280 g
Status Jun 6, 2014

Write a review

Note: HTML is not translated!

Rating: Bad Good

Enter the code in the box below:

Continue