- |
SIMATIC DP, DISTRIBUTED I/O ET200X:BASIC MOD. BM143/DESINA 8DI/DO CONFIGURABLE,ADD.DIAG- INPUTS,HYBRID FIELD BUS INTERF. (RS485), IDENT CONNECTOR, IP67 |
|
| Supply voltage |
| Load voltage 1L+ |
| Rated value (DC) |
24 V |
| Reverse polarity protection |
No |
| Load voltage 2L+ |
| Rated value (DC) |
24 V |
| Reverse polarity protection |
No |
| Input current |
| from load voltage 1L+ (unswitched voltage) |
180 mA |
| from load circuit 1 (unswitched voltage/supply voltage) up to 40 °C |
10 A |
| from load circuit 1 (unswitched voltage/supply voltage) up to 55 °C |
8 A |
| from load circuit 2 (unswitched voltage/supply voltage) up to 40 °C |
10 A |
| from load circuit 2 (unswitched voltage/supply voltage) up to 55 °C |
8 A |
| Power losses |
| Power loss, typ. |
3.5 W |
| Hardware configuration |
| Expansion modules |
| Number of expansion modules, max. |
7 |
| of which motor starters/frequency converters, max. |
6 |
| of which, pneumatic interfaces, max. |
6 |
| Digital inputs |
| Number of digital inputs |
8; 8 process channels, parameterization as DI/DO; 8 function channels, parameter assignment as diagnostics/NC input |
| Input characteristic curve in accordance with IEC 61131, type 2 |
Yes |
| Input voltage |
| Rated value, DC |
24 V; Input voltage for parameterized DI (Pin 4): Rated value 24 VDC, for signal "1": 13 to 30 V, for signal "0": -30 to +5 V: Input voltage for input functionality (Pin 2): Rated value 24 VDC, for signal "1": 13 to 30 VDC, for signal "0": -30 to +2 V |
| for signal "0" |
-3 to +5 V |
| for signal "1" |
13 to 30 V |
| Input current |
| for signal "1", typ. |
5 mA |
| Input delay (for rated value of input voltage) |
| for standard inputs |
| at "0" to "1", min. |
1.2 ms |
| at "0" to "1", max. |
4.8 ms |
| Cable length |
| Cable length unshielded, max. |
30 m; for signal lines |
| Digital outputs |
| Number of digital outputs |
8; 8 process channels, parameterization as DI/DO; 8 function channels, parameter assignment as diagnostics/NC input |
| Short-circuit protection |
Yes; Electronic |
| Response threshold, typ. |
1,8 A |
| Switching capacity of the outputs |
| Lamp load, max. |
10 W |
| Output current |
| for signal "1" rated value |
1.2 A |
| for signal "1" permissible range for 0 to 60 °C, min. |
5 mA |
| for signal "1" permissible range for 0 to 60 °C, max. |
1.3 A |
| for signal "0" residual current, max. |
0.5 mA |
| Switching frequency |
| with resistive load, max. |
100 Hz |
| with inductive load, max. |
2 Hz |
| on lamp load, max. |
1 Hz |
| Aggregate current of outputs (per group) |
| all mounting positions |
| up to 60 °C, max. |
Simultaneity factor 50% |
| Cable length |
| Cable length unshielded, max. |
30 m |
| Encoder |
| Connectable encoders |
| 2-wire sensor |
Yes |
| Permissible quiescent current (2-wire sensor), max. |
1.5 mA |
| 1st interface |
| Functionality |
| DP slave |
Yes |
| DP slave |
| Transmission rate, min. |
9.6 kbit/s |
| Transmission rate, max. |
12 Mbit/s; 9,6 / 19,2 / 45,45 / 93,75 / 187,5 / 500 kbit/s; 1,5 / 12 Mbit/s |
| Services |
| Direct data exchange (slave-to-slave communication) |
Yes; Sender |
| Interrupts/diagnostics/status information |
| Alarms |
| Diagnostic alarm |
Yes |
| Diagnostic messages |
| Diagnostics |
Yes; complying with DESINA |
| Diagnostics indication LED |
| Group error SF (red) |
Yes |
| Galvanic isolation |
| Galvanic isolation |
No electrical isolation between the load voltages and between the load voltages and all the other circuit components |
| between PROFIBUS DP and all other circuit components |
Yes |
| Galvanic isolation digital inputs |
| between the channels |
No |
| between the channels and the backplane bus |
No |
| Degree and class of protection |
| IP67 |
Yes |
| Dimensions |
| Width |
175 mm; 180 when screw mounted |
| Height |
180 mm; 174 when screw mounted |
| Depth |
110 mm; 90 when screw mounted |
| Status |
Jun 16, 2014 |
