6ES7132-1BH00-0XB0 ET200L, EL-BLOCK, 16DO, DC 24V, 0.5A

6ES7132-1BH00-0XB0 ET200L, EL-BLOCK, 16DO, DC 24V, 0.5A

Product Code: 6ES7132-1BH00-0XB0

Availability: In Stock

Price: $143.51
Qty:
Add to Wish List
Add to Compare
  
 
ET 200L

-
SIMATIC DP, ELECTRONIC BLOCK FOR ET 200L, 16 DO, 24V DC/0.5A
General information
Vendor identification (VendorID) 0016h
Supply voltage
24 V DC Yes
Reverse polarity protection Yes
Mains buffering
Mains buffering, min. 20 ms
Load voltage 2L+
Rated value (DC) 24 V; 1L+, 2L+, 3L+
Input current
from load voltage L1 (without load), max. 50 mA; Per load group (L1+ or L2+ / L3+)
Hardware configuration
Rack
Required terminal block TB 16L
Digital outputs
Number of digital outputs 16
short-circuit protection Yes
Response threshold, typ. 0,7 A
Limitation of inductive shutdown voltage to Typ. (L1+ or L2+ / L3+) -55 V
Controlling a digital input Yes
Switching capacity of the outputs
Lamp load, max. 5 W
Load resistance range
lower limit 41 Ω
upper limit 28000 Ω
Output voltage
Rated value (DC) 24 V
for signal "1", min. Ua - 3 V
Output current
for signal "1" rated value 0.5 A
for signal "1" permissible range for 0 to 60 °C, max. 0.5 A
Output delay with resistive load
"0" to "1", max. 50 ms
"1" to "0", max. 200 ms
Parallel switching of 2 outputs
for increased power No
for redundant control of a load Yes; only outputs of the same group
Switching frequency
with resistive load, max. 100 Hz
with inductive load, max. 0.5 Hz
on lamp load, max. 8 Hz
Aggregate current of outputs (per group)
all mounting positions
up to 60 °C, max. 4 A
horizontal installation
up to 40 °C, max. 3000 mA
up to 60 °C, max. 2000 mA
all other mounting positions
up to 40 °C, max. 2 A
Cable length
Cable length, shielded, max. 1000 m
Cable length unshielded, max. 600 m
Interfaces
PROFIBUS DP
Transmission rate, max. 1.5 Mbit/s
Direct data exchange (slave-to-slave communication) Yes; Transmitter (for digital outputs and hybrid modules ET 200L: not for L-SC or IM-SC)
Communication functions
Bus protocol/transmission protocol PROFIBUS DP
Interrupts/diagnostics/status information
Alarms
Alarms No
Diagnostic messages
Diagnostic functions Yes
Diagnostics indication LED
Bus fault BF (red) Yes
Status indicator digital output (green) Yes
Status indicator digital input (green) Yes
Monitoring 24 V voltage supply ON (green) Yes
Galvanic isolation
between PROFIBUS DP and all other circuit components Yes
Galvanic isolation digital outputs
between the channels No
between the channels and PROFIBUS DP Yes; Optocoupler
Isolation
Isolation checked with 500 V DC
Degree and class of protection
IP20 Yes
Ambient conditions
Operating temperature
horizontal installation, min. 0 °C
horizontal installation, max. 60 °C; 40°C for other mountings
Air pressure
permissible range, min. 795 hPa
permissible range, max. 1080 hPa
Relative humidity
Operation, min. 5 %
Operation, max. 95 %; RH class 2 in accordance with IEC 1131-2
Vibrations
Operation, checked according to IEC 60068-2-6 Yes; IEC 68, Part 2-6; 10 to 57 Hz; (constant amplitude 0.075 mm); 57 to 150 Hz; (constant acceleration 1 g)
Shock test
checked according to IEC 60068-2-27 Yes; IEC 68, Part 2-27; half-sine, 15 g, 11 ms
Connection method
Inputs/outputs Screw-type and spring-loaded terminals, permanent wiring; standard: 2-wire connection, optional: 3 and 4-wire connection
Dimensions
Width 145 mm
Height 60 mm
Depth 60.5 mm
Weights
Weight, approx. 130 g
Status Feb 10, 2014

Write a review

Note: HTML is not translated!

Rating: Bad Good

Enter the code in the box below:

Continue