 |
|
| Supply voltage |
| Load voltage L+ |
| ● Rated value (DC) |
24 V |
| Input current |
| from backplane bus 5 V DC, max. |
60 mA |
| from supply voltage L+, max. |
150 mA |
| Output voltage |
| Power supply to the transmitters |
| ● present |
Yes |
| ● Rated value (DC) |
13 V; at 22 mA |
| ● No-load voltage (DC) |
25.2 V |
| Power losses |
| Power loss, typ. |
3 W |
| Analog inputs |
| Number of analog inputs |
4 |
| permissible input current for current input (destruction limit), max. |
40 mA |
| Input ranges |
| ● Current |
Yes |
| Input ranges (rated values), currents |
| ● 0 to 20 mA |
Yes |
| ● Input resistance (0 to 20 mA) |
50 Ω |
| ● 4 to 20 mA |
Yes |
| ● Input resistance (4 to 20 mA) |
50 Ω |
| Cable length |
| ● Cable length, shielded, max. |
200 m |
| Analog value creation |
| Measurement principle |
Sigma Delta |
| Integration and conversion time/resolution per channel |
| ● Resolution with overrange (bit including sign), max. |
16 bit; 10 to 15 bits + sign |
| ● Integration time, parameterizable |
Yes; 2.5 to 100 ms |
| ● Interference voltage suppression for interference frequency f1 in Hz |
10 to 400 Hz |
| Encoder |
| Connection of signal encoders |
| ● for current measurement as 2-wire transducer |
Yes |
| ● for current measurement as 4-wire transducer |
Yes |
| Errors/accuracies |
| Operational limit in overall temperature range |
| ● Current, relative to input area, (+/-) |
0.45 % |
| Basic error limit (operational limit at 25 °C) |
| ● Current, relative to input area, (+/-) |
0.1 % |
| Interference voltage suppression for f = n x (f1 +/- 1 %), f1 = interference frequency |
| ● Series mode interference (peak value of interference < rated value of input range), min. |
60 dB |
| ● Common mode interference, min. |
130 dB |
| Interrupts/diagnostics/status information |
| Diagnostic messages |
| ● Diagnostic functions |
Yes |
| ● Diagnostic information readable |
Yes |
| ● Overrange |
Yes |
| ● Wire break in signal transmitter cable |
Yes |
| ● Short circuit of the signal encoder cable |
Yes |
| Diagnostics indication LED |
| ● Short circuit per channel (red) |
Yes |
| ● Short-circuit group error (red) |
Yes |
| Ex(i) characteristics |
| Module for Ex(i) protection |
Yes |
| Max. values of input circuits (per channel) |
| ● Co (permissible external capacity), max. |
90 nF |
| ● Io (short-circuit current), max. |
68.5 mA |
| ● Lo (permissible external inductivity), max. |
7.5 mH |
| ● Po (power of load), max. |
431 mW |
| ● Ri, max. |
50 Ω |
| ● Uo (output no-load voltage), max. |
25.2 V |
| Galvanic isolation |
| Galvanic isolation analog inputs |
| ● Galvanic isolation analog inputs |
Yes |
| Permissible potential difference |
| between the inputs (UCM) |
60 V DC/30 V AC when used in the hazardous area; 400 V DC/250 V AC when used in NON-hazardous area |
| between inputs and MANA (UCM) |
60 V DC/30 V AC when used in the hazardous area; 400 V DC/250 V AC when used in NON-hazardous area |
| Standards, approvals, certificates |
| Use in hazardous areas |
| ● Type of protection acc. to EN 50020 (CENELEC) |
[EEx ib] IIC |
| ● Type of protection acc. to FM |
Class I, Division 2, Group A, B, C, D T4 |
| ● Test number PTB |
Ex-96.D.2092X |
| Ambient conditions |
| Operating temperature |
| ● max. |
60 °C |
| Connection method |
| required front connector |
20-pin |
| Weights |
| Weight, approx. |
290 g |
| last modified: |
25.09.2014 |
