6ES7134-7SD51-0AB0 ET200ISP, EL-MOD., 4 AI RTD, PT100/NI100

6ES7134-7SD51-0AB0 ET200ISP, EL-MOD., 4 AI RTD, PT100/NI100

Product Code: 6ES7134-7SD51-0AB0

Availability: In Stock

Price: $307.57
Qty:
Add to Wish List
Add to Compare
  
 
Analog input module 4 AI I 2 WIRE HART

-
SIMATIC DP, ELECT. SUBMODULE FOR ET200ISP, 4 AI, RTD, FOR CONNECTION OF RESISTANCE THERMOMETER PT100/NI100
Input current
from supply voltage L+, max. 22 mA
Power losses
Power loss, typ. 0.4 W
Analog inputs
Number of analog inputs 4
Cycle time (all channels) max. 320 ms; 66 ms basic conversion time x 4 channels with 60 Hz interference frequency suppression; 80 ms basic conversion time x 4 channels with 50 Hz interference frequency suppression
Technical unit for temperature measurement adjustable Yes
Input ranges
Voltage No
Current No
Thermocouple No
Resistance thermometer Yes
Resistance Yes
Input ranges (rated values), resistance thermometers
Ni 100 Yes
Input resistance (Ni 100) 2000 kΩ
Pt 100 Yes
Input resistance (Pt 100) 2000 kΩ
Input ranges (rated values), resistors
0 to 600 ohms Yes; Also 1000 ohms
Input resistance (0 to 600 ohms) 1000 kΩ
Resistance thermometer (RTD)
Characteristic linearization
for resistance thermometer Yes
Characteristic linearization
Parameterizable Yes
Cable length
Cable length, shielded, max. 500 m
Analog value creation
Measurement principle integrating (Sigma-Delta)
Integrations and conversion time/resolution per channel
Resolution with overrange (bit including sign), max. 16 bit
Integration time, parameterizable Yes
Basic conversion time, including integration time, ms 80 ms at 50 Hz; 66 ms at 60 Hz
additional conversion time for wire break monitoring 5
Interference voltage suppression for interference frequency f1 in Hz 50 / 60 Hz
Smoothing of measured values
Parameterizable Yes; in 4 stages
Step: None Yes; 1 x cycle time
Step: low Yes; 4 x cycle time
Step: Medium Yes; 32 x cycle time
Step: High Yes; 64 x cycle time
Encoder
Connection of signal encoders
for resistance measurement with two-wire connection Yes
for resistance measurement with three-wire connection Yes
for resistance measurement with four-wire connection Yes
Errors/accuracies
Linearity error (relative to input range), (+/-) 0.015 %
Temperature error (relative to input range), (+/-) 0.02 %/K
Crosstalk between the inputs, min. -50 dB
Repeat accuracy in steady state at 25 °C (relative to input area), (+/-) 0.01 %
Operational limit in overall temperature range
Resistance thermometer, relative to input area, (+/-) 0.15 %; Applies to resistances standard +/- 0.8K climatic +/- 0.3K
Basic error limit (operational limit at 25 °C)
Resistance thermometer, relative to input area, (+/-) 0.1 %; Applies to resistances standard +/- 0.5 K climatic +/- 0.2 K
Interference voltage suppression for f = n x (f1 +/- 1 %), f1 = interference frequency
Series mode interference (peak value of interference < rated value of input range), min. 70 dB
Common mode interference, min. 90 dB
Interrupts/diagnostics/status information
Alarms
Diagnostic alarm Yes
Limit value alarm Yes
Diagnostic messages
Diagnostic information readable Yes
Wire break Yes
Short circuit Yes
Group error Yes
Diagnostics indication LED
Group error SF (red) Yes
Galvanic isolation
Galvanic isolation analog inputs
between the channels No
between the channels and the backplane bus Yes
between the channels and the load voltage L+ Yes; Channels and power bus
Standards, approvals, certificates
CE mark Yes
Highest safety class achievable in safety mode
acc. to IEC 61508 none
Performance level according to EN ISO 13849-1:2008 none
Use in hazardous areas
Type of protection acc. to EN 50020 (CENELEC) II2 G (1) GD Ex ib[ia] IIC T4 and I M2 Ex ib[ia] I
Type of protection acc. to KEMA 04 ATEX 1247
Dimensions
Width 30 mm
Height 129 mm
Depth 136.5 mm
Weights
Weight, approx. 230 g
Status Jun 16, 2014

Write a review

Note: HTML is not translated!

Rating: Bad Good

Enter the code in the box below:

Continue