6ES7134-0KH01-0XB0 ET200B, EL-MOD., 8AI, THERMO/PT100

Product Code: 6ES7134-0KH01-0XB0

Availability: In Stock

Price: $785.70
Qty:
Add to Wish List
Add to Compare
  
 
SIMATIC DP, ELECTRONIC MODULE ANALOG, FOR ET 200B, W=160MM, 8AI (THERMOCOUPLES) OR 4AI (PT100); 12 BIT
Supply voltage
permissible range, lower limit (DC) 18.5 V
permissible range, upper limit (DC) 30.2 V
Load voltage 1L+
Rated value (DC) 24 V; Value at t < 0.5 s: 35 V
Input current
Digital outputs
from load voltage L+, max. 80 mA; Logic
Power losses
Power loss, typ. 2 W
Hardware configuration
Rack
Required terminal block TB8
Analog inputs
Number of analog inputs 8; 8 voltage inputs/thermocouples or 4 Pt100, Ni100
permissible input voltage for voltage input (destruction limit), max. 32 V
Input ranges
Voltage Yes
Thermocouple Yes
Resistance thermometer Yes
Resistance Yes
Input ranges (rated values), voltages
-1 V to +1 V Yes
Input resistance (-1 V to +1 V) 10 Ω
-250 mV to +250 mV Yes
Input resistance (-250 mV to +250 mV) 10 Ω
-500 mV to +500 mV Yes
Input resistance (-500 mV to +500 mV) 10 Ω
-80 mV to +80 mV Yes
Input resistance (-80 mV to +80 mV) 10 Ω
Input ranges (rated values), thermoelements
Type E Yes
Type J Yes
Type K Yes
Type L Yes
Type N Yes
Type R Yes
Type T Yes
Type U Yes
Input ranges (rated values), resistance thermometers
Ni 100 Yes
Pt 100 Yes
Input ranges (rated values), resistors
0 to 150 ohms Yes
0 to 300 ohms Yes
0 to 48 ohms Yes
0 to 600 ohms Yes
Thermocouple (TC)
Characteristic linearization
for thermocouples Type E, J, K, L, N, T, U
Cable length
Cable length, shielded, max. 100 m
Analog value creation
Measurement principle Integrating voltage/time conversion
Integrations and conversion time/resolution per channel
Resolution with overrange (bit including sign), max. 12 bit; Two''s complement
Integration time, parameterizable Yes; 2,5 / 16,67 / 20 / 100 ms
Basic conversion time, including integration time, ms 8 / 35 / 42 / 200
additional conversion time for wire break monitoring 10 / 10 / 10 / 10 ms
Interference voltage suppression for interference frequency f1 in Hz 400 / 60 / 50 / 10 Hz
Encoder
Connection of signal encoders
for resistance measurement with two-wire connection Yes
for resistance measurement with four-wire connection Yes
Errors/accuracies
Linearity error (relative to input range), (+/-) 0.05 %
Temperature error (relative to input range), (+/-) 0.0050 %/K
Crosstalk between the inputs, min. 50 dB; At 50/60 Hz
Repeat accuracy in steady state at 25 °C (relative to input area), (+/-) 0.05 %
Operational limit in overall temperature range
Voltage, relative to input area, (+/-) 1 %; At 80 mV; +/-0.6 % from 250 to 1000 mV
Resistance, relative to input area, (+/-) 1 %
Basic error limit (operational limit at 25 °C)
Voltage, relative to input area, (+/-) 0.6 %; at 80 mV; +/-0.4% from 250 to 1000 mV
Resistance, relative to input area, (+/-) 0.6 %
Interference voltage suppression for f = n x (f1 +/- 1 %), f1 = interference frequency
Series mode interference (peak value of interference < rated value of input range), min. 40 dB
Common mode interference, min. 70 dB; Upp < 3 V
Interfaces
PROFIBUS DP
Transmission rate, max. 12 Mbit/s
Communication functions
Bus protocol/transmission protocol PROFIBUS DP
Interrupts/diagnostics/status information
Alarms
Diagnostic alarm Yes; Parameterizable
Limit value alarm Yes; Parameterizable, channels 0 and 2
Diagnostic messages
Overrange Yes; Overrange
Wire break in signal transmitter cable Yes; For Pt 100, Ni 100, R, +/- -80 mV, thermocouples type E, J, K, L, N, T, U (parameterizable)
Diagnostics indication LED
Bus fault BF (red) Yes
Run mode RUN (green) Yes
Galvanic isolation
between electronic block and PROFIBUS DP Yes
Galvanic isolation analog inputs
Galvanic isolation analog inputs No
Permissible potential difference
between the inputs (UCM) max. +/- 1 V
between inputs and MANA (UCM) max. +/- 1 V
Degree and class of protection
IP20 Yes
Ambient conditions
Operating temperature
horizontal installation, min. 0 °C
horizontal installation, max. 60 °C; 40°C for other mountings
Air pressure
permissible range, min. 795 hPa
permissible range, max. 1080 hPa
Relative humidity
Operation, min. 15 %
max. relative humidity 95 %; RH class 2 in accordance with IEC 1131-2
Vibrations
Operation, checked according to IEC 60068-2-6 Yes; IEC 68, Part 2-6; 10 to 57 Hz; (constant amplitude 0.075 mm); 57 to 150 Hz; (constant acceleration 1 g)
Shock test
checked according to IEC 60068-2-27 Yes; IEC 68, Part 2-27; half-sine, 15 g, 11 ms
Connection method
Inputs/outputs Screw-type and spring-loaded terminals, permanent wiring; 3 and 4-wire connection
Dimensions
Width 160 mm; EB and TB
Height 130 mm; EB and TB
Depth 60 mm; EB and TB
Weights
Weight, approx. 550 g; EB and TB
Status Jun 16, 2014

Write a review

Note: HTML is not translated!

Rating: Bad Good

Enter the code in the box below:

Continue